🛡️ Licensed & Insured · TSBC Gas-Fitting LGA0043870 · Serving Metro Vancouver since 1999
★★★★★ 4.9 from 85+ Google reviews · info@canroheat.ca
Gas Fireplace Installation · Metro Vancouver

Do I need a gas line for a fireplace, and can you install one?

Yes — a gas fireplace needs a properly sized gas line run to the unit, and CANRO’s licensed gas fitters install it as part of the project. If your home already has natural gas, we extend a new branch line to the fireplace location; the cost depends mainly on the distance from the existing supply and the access along the route.
★ 4.9/5 · 85+ reviews✅ Licensed & TSBC gas-fitting🎉 Since 1999

Get your free quote

Tell us about your installation—we’ll call you back fast.

No obligation · We never share your info

How gas-line installation works

  1. Locate the existing gas supply and size the new branch for the fireplace’s demand.
  2. Run the line to the fireplace location, keeping access and clearances to code.
  3. Connect, pressure-test, and verify there are no leaks.
  4. Tie it into the permitted install and the TSBC inspection.

What affects gas-line cost

Distance from the meter/supply, whether walls or floors must be opened, and any required upsizing of the supply for added load. We assess all of this at the quote so the price is firm. See gas fireplace installation or book an assessment.

BC Permits and Technical Safety BC Requirements for Gas Fireplace Lines

In British Columbia, any new gas line installation — including a branch to a fireplace — requires a permit from Technical Safety BC and must be carried out by a licensed gas contractor. At CANRO, we hold gas licence LGA0043870, which authorizes us to pull this permit on your behalf. The permit triggers an inspection by a Technical Safety BC officer once the work is complete, confirming the line is correctly sized, properly supported, and leak-tested to provincial code. Skipping the permit is not just illegal; it can void your home insurance and create serious liability if a problem arises later.

  • Permit is mandatory — no exceptions for BC residential gas work, regardless of scope.
  • Licensed contractor only — homeowners cannot self-perform gas line extensions in BC.
  • Pressure test required — the completed line must hold pressure before the inspection passes.
  • As-built documentation — your contractor should provide a copy of the permit and inspection record for your home file.
  • Appliance connection — the fireplace itself must also be installed and commissioned by a licensed gas fitter before first use.

Because CANRO technicians are Red Seal certified and have worked under Technical Safety BC requirements since 1999, we handle the permit application, scheduling, and inspection coordination for you. Most residential gas fireplace line permits in Metro Vancouver are straightforward and do not add significant time to a project — typically the inspection can be booked within a few business days of rough-in completion. Call us at (604) 359-1081 or visit our contact page to get a permit-included quote.

What to Expect on Installation Day: A Step-by-Step Overview

Many Metro Vancouver homeowners are nervous about gas work because they are not sure what the crew will need to access or how disruptive the day will be. In most older detached homes and townhomes in the region, the gas meter feeds a main line in the utility room or crawlspace, and the fireplace location is typically a living room or family room on the same floor — a relatively short run. Newer condos add a layer of coordination with building management, since the gas riser is common property. Here is what a typical installation day looks like.

  1. Site walkthrough — the technician confirms the routing path, checks existing gas load on the meter, and identifies any wall cavities, joists, or fireblocking that affect the run.
  2. Gas shutoff — the main gas supply to your home is shut off for a short period while the tee and new valve are installed on the existing line.
  3. Line routing — black iron or corrugated stainless steel tubing (CSST) is run through the wall or floor cavity to the fireplace alcove; small access holes are patched after.
  4. Appliance connection — a flexible gas connector and shutoff valve are installed at the fireplace location per BC code.
  5. Pressure test and leak check — the entire new section is tested and every joint is checked with a gas-detector or soap solution before the main is reopened.
  6. Commissioning and handoff — the technician lights the fireplace, verifies pilot and flame operation, and walks you through safe operating procedures.

How CANRO handles your gas fireplace installation

Every CANRO installation follows the same honest, code-driven process so there are no surprises: a free in-home assessment and correct sizing, a written upfront price, clean professional installation by our licensed technicians, full commissioning, and a passed inspection—with the TSBC gas permit handled for you. We’ve served Metro Vancouver since 1999 and are rated 4.9 stars across 85+ Google reviews. Explore gas fireplace installation.

Keep reading

Related installation questions

Good to know

More frequently asked questions

Can you add a gas line if I only have electric?
If natural gas service reaches your property, we can bring it in and run a line. If there’s no gas service at all, propane is the alternative.
How much does a gas line for a fireplace cost?
It depends on distance and access; a short run near the supply is modest, while a long run through finished walls costs more. We quote it precisely.
Is the gas line included in the fireplace quote?
Yes — the gas line, connection, permit and inspection are part of the installation quote.
Do you pressure-test the line?
Always — every gas line is pressure-tested and leak-checked before the unit is commissioned.
Can my existing gas meter handle a fireplace on top of my furnace and hot water heater?
In most Metro Vancouver homes built before 2000, the gas meter was sized for a furnace and water heater, with some headroom left over. A standard gas fireplace insert draws roughly 25,000 to 40,000 BTU/h, which is well within what most residential meters can support. However, if you also have a gas range or dryer, or if you are adding a high-output fireplace, our technician will calculate the total connected load and confirm capacity before running the line. In rare cases, FortisBC can upsize the meter at no cost to you — we coordinate that request on your behalf.
Will a new gas line for a fireplace affect my home insurance or require notification to my insurer?
Yes — you should notify your home insurer once the work is complete and the Technical Safety BC inspection has passed. Most BC insurers require that any gas appliance addition be performed by a licensed contractor with a closed permit, which is exactly what CANRO provides. Giving your insurer a copy of the permit and inspection record typically satisfies their documentation requirement and prevents any coverage dispute in the event of a future claim. Some insurers will ask for the contractor's licence number; ours is LGA0043870. Never let a contractor do gas work without pulling a permit — an unpermitted line can be grounds for a denied claim.

Need heat, hot water or cooling? Talk to a real technician today.

25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.

📞 Call (604) 359-1081 Get a free quote →
📞 Call nowFree quote