A cold John Wood tank in Port Coquitlam usually traces to a pilot or gas fault, and older homes with tight utility closets add a venting clearance check to the list.
Tell us what you need—we’ll call you back fast.
Quick answer
No hot water from a John Wood gas tank water heater is typically a pilot or ignition failure, an interrupted gas supply, a tripped safety switch, or sediment buildup heavy enough to affect the burner. In Port Coquitlam's older homes, restricted combustion air in a tight utility closet can also contribute to ignition problems, so that's worth checking alongside the usual causes.
Need a licensed gas fitter for your tank water heater? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
When a gas tank water heater stops delivering hot water, the fault is almost always one of a handful of things: the pilot or ignition system has failed, gas isn't reaching the burner, a safety switch has shut the unit down deliberately, or sediment buildup has gotten heavy enough to interfere with heat transfer. On John Wood tanks, a worn thermocouple or thermopile is a common cause since it's a wear part that fails gradually rather than all at once, and a homeowner often notices the pilot going out more and more frequently before it finally won't stay lit at all.
Many Port Coquitlam homes date to the 1970s and 80s era of bungalow and split-level construction that shaped much of the Tri-Cities area, and their utility closets were often built to fit the smaller tanks standard at the time. In a tight space like that, it's not unusual for combustion air openings to get partially blocked over the years by stored items, and a starved combustion air supply can cause a pilot to burn poorly or a safety sensor to intermittently fail to detect a stable flame. It's a different mechanism than a genuinely failed thermocouple, but it can produce similar symptoms, which is why a technician diagnosing a no-hot-water call in one of these older homes checks clearance around the unit as a matter of course.
Newer construction elsewhere in Port Coquitlam generally has more generous mechanical room sizing, so this particular contributor is mostly relevant to the city's older housing stock.
| Check | Purpose |
|---|---|
| Gas supply pressure | Confirms fuel is reaching the control valve |
| Pilot and thermocouple | Isolates ignition fault from a safety-device issue |
| Combustion air clearance | Rules out a starved burner in a tight closet |
| High-limit switch state | Shows whether shutdown was intentional |
| Sediment depth | Confirms whether recovery loss is a flushing issue |
If diagnosis lands on the pilot, thermocouple, or gas valve, that's a standard repair and doesn't call the tank itself into question. If the visit instead turns up rust-coloured water, a leak from the tank body, or a pattern of repeat ignition failures despite adequate clearance, that points toward the tank nearing the end of its service life rather than a fixable component issue, and replacement becomes the more sensible conversation.
Safety note
If you smell gas at any point, leave the home immediately and call FortisBC at 1-800-663-9911 from a safe location. Diagnosing and repairing gas ignition systems, gas valves, and combustion air issues must be handled by a Technical Safety BC licensed gas fitter.
If they block the combustion air opening, yes — a starved burner can struggle to maintain a stable pilot flame, which is a more common issue in Port Coquitlam's older, tighter utility closets than in newer, more open mechanical rooms.
A licensed gas fitter can confirm whether your specific install meets current clearance requirements; as a general rule, keeping stored items well clear of the unit's air openings and venting connection is a reasonable precaution regardless.
They can produce similar symptoms, like a pilot that won't stay lit, but a thermocouple is a worn part that needs replacing while a combustion air issue is fixed by clearing space and airflow around the unit — a technician will differentiate the two during diagnosis.
Repeated failures usually point to either a worn thermocouple or a draft or airflow issue in the mechanical space, both of which are worth having checked rather than continuing to relight it repeatedly.
The underlying causes are the same across the region — the main local wrinkle is that Port Coquitlam has a larger share of older homes with tighter utility closets than some newer-built areas nearby.
Avoid repeatedly relighting the pilot if it won't hold, and don't attempt to move items around a suspected blocked vent yourself if you're unsure — leave it for the technician to assess safely.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”

“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”

“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”

25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.