What goes into a Rinnai i-Series replacement decision and installed cost in Delta.
Tell us what you need—we’ll call you back fast.
Quick answer
Replacing a Rinnai i-Series in Delta makes sense when a repair no longer pencils out — a major component failure on an older unit, or a heating load the boiler was never sized for. Installed cost typically runs $6,500–$14,000+ for the boiler itself or $7,500–$15,000+ for a full replacement, as a 2026 public-market ballpark, not a quote.
Need a licensed gas fitter for your gas boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
Replacing a Rinnai i-Series boiler in Delta raises the same core question homeowners face anywhere — repair versus replace — but the answer often turns on details specific to Delta's housing and terrain.
For a Delta property specifically, a single failed component on a unit under roughly ten years old with a clean service record is still usually worth repairing rather than replacing outright. What changes the calculus here is how much a heat exchanger or control board failure on an older unit costs to chase down given Delta's flood-plain drainage constraints — at that point, replacement usually pencils out better.
Delta sits in low-lying land on the Fraser River delta, much of it near or below sea level, and the local housing stock — older character homes in Ladner and South Delta where basements sit close to a naturally high water table, which matters for where a condensate line can drain and how a mechanical room handles any moisture — affects how much of a replacement job is boiler swap versus venting rework. A higher water table near the river in parts of this area affects where a condensate line can safely terminate, which is worth flagging at the assessment.
Gas line condition is worth checking too — a Delta home that's added appliances or square footage over the years may need the interior gas piping upsized to feed the new i-Series alongside everything else already running on the meter.
A proper heat-loss calculation for a Delta property — not just matching the old boiler's nameplate — is what determines the right size for the new i-Series, especially if the home has had an addition, a basement suite added, or insulation upgrades since the original boiler went in. A unit sized larger than the calculation supports will tend to short-cycle on milder coastal days instead of modulating down the way it's designed to.
Because municipal water in this part of Metro Vancouver runs soft, sizing and venting matter more for the new unit's long-term reliability in Delta than water treatment does — though on a well-water property nearby, a technician may still flag whether a scale-reducing measure on the domestic hot-water side is worth discussing for a combi install.
| Scope | 2026 ballpark (CAD) |
|---|---|
| Boiler install | $6,500–$14,000+ |
| Full boiler replacement | $7,500–$15,000+ |
| Combi boiler installed | $9,000–$16,000 |
| Gas permit | $75–$200 |
Those figures are 2026 public-market ballparks for budgeting, not a quote for your specific Delta job — CANRO's certified technicians confirm the real number once they've seen the mechanical room and venting run in person.
Permitting for a Delta replacement is filed through the Corporation of Delta, and CANRO handles that submission as part of the job rather than leaving it for the homeowner to sort out.
Before a technician comes out to a Delta property, it's worth locating the boiler's model plate, noting roughly how old the unit is, and thinking through whether the home's heating or hot-water demand has changed since it was installed — an addition, a converted basement, or a new bathroom all affect sizing. That short list of information, combined with an in-person look at the mechanical room and venting run, is what lets CANRO give a firm number instead of a wide guess.
Safety note
If you smell gas near the boiler, hear a hissing sound at a fitting, or a carbon monoxide alarm goes off, get everyone out of the house first and call from outside. Do not flip switches, light anything, or go looking for the source yourself. FortisBC's emergency line is 1-800-663-9911 and they will tell you when it's safe to go back in; a licensed gas fitter should confirm the fix before the i-Series is fired back up.
It depends on venting and access, which varies enough between properties here that a real timeline only comes from an in-person look rather than a phone estimate.
Not necessarily for the exterior portion, but access to the mechanical room inside is needed, so coordinate scheduling with the technician.
The paperwork goes through the Corporation of Delta specifically — CANRO handles that submission as part of a replacement job.
Often yes for a straightforward swap with compatible venting; jobs needing venting rework or gas line upsizing can take longer, which the assessment will clarify.
Only if a heat-loss and hot-water-demand calculation actually supports it — bigger isn't automatically better, and correct sizing matters more for efficiency than headroom.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.