A Tsawwassen-specific look at diagnosing and repairing a Takagi T-H3 tankless water heater, including the coastal wear pattern local units show.
Tell us what you need—we’ll call you back fast.
Quick answer
On the Tsawwassen peninsula, a Takagi T-H3 that's misfiring or losing hot water is often dealing with the same ignition or scale issues as anywhere else, but exterior vent hardware here corrodes faster because of the salt air off the water, so that's the first thing we check. A hands-on inspection tells us whether it's a venting, ignition, or heat-exchanger problem.
Need a licensed gas fitter for your tankless water heater? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
Tsawwassen sits out on its own peninsula within the Corporation of Delta, close enough to the water that salt-laden air is a real factor for anything mounted outside, including the vent terminal and exterior cap on a tankless water heater. We see faster corrosion on exterior venting hardware here than in inland Delta or Surrey, particularly on homes closer to the beach or the ferry terminal side of the community.
The housing mix runs from older beach-adjacent cottages and 1970s-80s split-levels to newer subdivisions further from the water. On the older homes, the T-H3 is frequently in an attached garage or a small utility room with a short exterior vent run straight through the wall facing the prevailing wind and salt spray, which is exactly the run that shows corrosion first.
That correlation with wind and rain is not a coincidence. A vent terminal partially restricted by corrosion behaves differently under high wind, sometimes allowing the unit to fire and sometimes not, which is why a fault that seems random often has a very physical, very findable cause once we get up to the vent cap itself.
We start outside with the vent terminal and intake screen, since that's the component most exposed to Tsawwassen's coastal conditions, checking for corrosion, salt residue, and physical obstruction. From there we verify gas pressure, then move inside to the flame sensor, igniter, and heat exchanger condition.
Takagi's fault categories span ignition, flame loss, venting restriction, water flow, and overheat protection, and on a coastal property we lean harder on the venting category as a starting hypothesis before assuming an internal electronic failure, simply because of what we see repeatedly out here.
You can visually look at the exterior vent cap from a safe distance for obvious white or green corrosion buildup and note whether faults seem to happen more during storms — that observation genuinely helps us diagnose faster. Don't attempt to clean, scrape, or remove the vent cap yourself, and don't reset the unit repeatedly if it keeps failing to relight.
If you notice a gas odour anywhere near the unit, treat it as an emergency rather than a maintenance item. Corrosion-related venting problems are a technician's job precisely because a partially blocked vent interacts with combustion in ways that aren't safe to troubleshoot by trial and error.
As a 2026 public-market ballpark, not a quote, a diagnostic service call runs about $90–$150 and is typically credited toward the repair, with typical tankless repairs in the $250–$900 range. CANRO's certified technicians confirm the exact figure once they've assessed your unit, since venting hardware replacement due to corrosion is priced differently than an internal sensor swap.
Homes right along the waterfront sometimes need more frequent vent hardware attention than homes a few blocks inland, which your technician will point out if it applies to your property.
If your vent terminal and connection hardware are showing significant corrosion on a unit already past the ten-year mark, replacement with fresh venting hardware is often the more sensible move than repeatedly patching an aging system exposed to the same salt air that caused the original wear.
Safety note
If you smell gas near the unit at any time, leave the home immediately and call FortisBC at 1-800-663-9911 from outside before doing anything else. Venting, gas line, and internal repairs on a tankless water heater must be performed by a Technical Safety BC licensed gas fitter, never attempted as a DIY fix.
Yes, salt-laden coastal air accelerates corrosion on exterior metal components, especially vent terminals and connection hardware, more than it affects the sealed internal parts of the unit.
A partially corroded or obstructed vent terminal reacts differently under wind pressure, which can cause intermittent ignition faults that seem to come and go with the weather.
Don't add anything to the vent terminal yourself — it's engineered for specific clearances and airflow, and an improvised cover can restrict combustion air or exhaust in ways that create a safety issue.
Work that changes or replaces venting components can require sign-off from the Corporation of Delta. Your technician will confirm whether your specific repair needs one.
An annual visual check as part of routine maintenance is reasonable for waterfront and near-waterfront properties, more often than we'd typically suggest for an inland installation.
Warranty terms are set by Takagi and vary by component and installation conditions — verify your certificate rather than assuming coverage either way.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”

“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”

“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”

25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.