Tankless · On-Demand · Condensing
Takagi Tankless Water Heaters in Metro Vancouver
Japanese-engineered tankless (on-demand) gas water heaters — high recovery, compact, no standby-heat loss.
By the CANRO Heating & Cooling technical team · Licensed HVAC & gas-fitting contractor, Metro Vancouver · Last updated July 2026
Why Takagi tankless works in Metro Vancouver
Takagi has been a mainstream tankless choice in Metro Vancouver for years — compact indoor and outdoor gas units that deliver continuous hot water without the standby heat loss of a storage tank. That matters here: BC natural-gas rates and FortisBC efficiency incentives make on-demand gas water heating one of the more cost-effective upgrades for homes with average-to-high hot-water demand. Takagi’s lineup spans standard non-condensing models and higher-efficiency condensing models.
TSBC-Licensed Gas FittersRed Seal HVACWorkSafeBC InsuredPermitted & Inspected InstallsServing Metro Vancouver Since 1999We File Your Rebates
Takagi tankless lineup CANRO installs & services here
The Takagi tankless models CANRO works with most across Metro Vancouver, with specs, the right use case, and typical installed cost.
Takagi Non-Condensing (Indoor / Outdoor)
Standard-efficiency tankless — lower upfront cost, proven platform
| Type | Non-condensing gas tankless, indoor or outdoor models |
|---|---|
| Capacity | Roughly 140,000–199,000 BTU/h, up to about 10 GPM depending on model and incoming water temperature |
| Efficiency | Uniform Energy Factor (UEF) in the ~0.80–0.85 range |
| Venting | Category III stainless steel (indoor models) |
| Best for | Like-for-like tank-to-tankless conversions where a simpler, lower-cost unit fits the home’s demand |
| Common issues we see | Scale buildup on hard-water routes, ignition/flame-sensor faults, undersized gas lines on retrofit installs |
| Typical install cost | $3,500–$5,500 installed |
Takagi Condensing
High-efficiency tankless — recovers exhaust heat, PVC venting
| Type | Condensing gas tankless |
|---|---|
| Capacity | Similar flow range to the non-condensing line, higher efficiency at the same output |
| Efficiency | UEF in the ~0.90–0.96 range — among the most efficient gas water heating available |
| Venting | PVC/CPVC — generally simpler and cheaper to route than stainless |
| Best for | Homes prioritizing lowest gas bills and best rebate eligibility |
| Common issues we see | Condensate-drain/neutralizer maintenance, scale buildup, freeze protection on exterior condensate lines |
| Typical install cost | $4,200–$6,800 installed before rebates |
Takagi Compact / Point-of-Use Models
Smaller-BTU units for a single fixture or small suite
| Type | Compact non-condensing tankless |
|---|---|
| Capacity | Lower BTU/GPM than full-house models |
| Best for | A secondary suite, laneway home, or a single high-demand fixture |
| Common issues we see | Undersizing for actual household demand — correct sizing is the most common failure point |
| Typical install cost | Quoted per install — smaller units are generally lower cost than full-house models |
CANRO’s Takagi experience
CANRO installs, services, and repairs Takagi tankless water heaters across Metro Vancouver. As TSBC-licensed gas fitters, we size the unit to your home’s peak demand (not just its square footage), get the gas line and venting right the first time — non-condensing units need Category III stainless venting, condensing units use PVC/CPVC — and handle the water-quality side (scale is the #1 cause of Takagi service calls in our harder-water service areas). We file FortisBC rebates where the unit qualifies.
Credentials: TSBC-licensed gas fitters · Red Seal HVAC · WorkSafeBC insured · permitted & inspected installs · manufacturer-trained · serving Metro Vancouver since 1999 · we file your CleanBC / FortisBC / BC Hydro rebates. Read our reviews →
Related pages
- Tankless hot water (hub) →
- Water heater installation in Metro Vancouver →
- Takagi no hot water →
- Takagi error code →
- Takagi scale buildup symptoms →
- Takagi ignition problem →
- Takagi cold water sandwich →
- Takagi water pressure problem →
- Takagi not enough hot water →
- Takagi flushing signs →
- FortisBC water-heater rebates →
Takagi Tankless FAQs from Metro Vancouver homeowners
Is Takagi a good tankless brand?+
Yes — Takagi is a long-established Japanese tankless manufacturer with a solid track record in Metro Vancouver. It’s a mainstream, dependable choice; CANRO also installs Rinnai, Navien, John Wood, Rheem, and Bosch tankless and will recommend honestly based on your home’s demand and venting situation.
Condensing or non-condensing Takagi?+
Condensing models cost more upfront but run more efficiently and vent with cheaper PVC/CPVC instead of stainless steel — often a wash or better on total installed cost, with lower ongoing gas bills. Non-condensing is a reasonable choice for straightforward, lower-demand replacements. CANRO sizes and quotes both so you can compare.
Why does my Takagi keep scaling up?+
Hard water accelerates mineral scale on the heat exchanger, which is the leading cause of reduced flow, error codes, and premature failure on tankless units generally. Metro Vancouver water is relatively soft citywide, but homes on well water or with older galvanized piping see more scale. Annual (or per-manufacturer-interval) descaling flushes are the fix.
Does a Takagi tankless qualify for a FortisBC rebate?+
Qualifying high-efficiency (condensing) tankless models are generally eligible for FortisBC natural-gas water-heater rebates. CANRO confirms your specific model’s eligibility before installing and files the paperwork.
How long does a Takagi tankless last?+
A properly sized, professionally installed, and regularly flushed Takagi typically lasts 15–20 years — longer than a typical tank water heater. Skipping annual descaling is the most common reason units fail early.
Can CANRO service a Takagi another company installed?+
Yes — we service, descale, and repair Takagi tankless units across Metro Vancouver regardless of who installed them, including units that were never sized or vented correctly.
Thinking about a Takagi tankless for your home?
Whether it’s a new Takagi tankless install, an annual descale/service, or a repair, CANRO covers all of Metro Vancouver. Call for honest advice and a free written quote.
4.9★85+ Google reviews
27+Years serving Metro Vancouver
20+Brands serviced
$0Free written estimates on installs
Frequently asked questions
How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. CANRO handles permits as part of every installation.
What HVAC services does CANRO offer in Metro Vancouver?
CANRO installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses and condos throughout the Lower Mainland.
How long has CANRO been in business?
CANRO has been serving the Greater Vancouver area since 1999. Our founder George is recognised by customers as one of the most experienced boiler and hydronic heating technicians in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
What Metro Vancouver homeowners say about CANRO
Verified Google reviews — 4.9 average across 85+ ratings
★★★★★
"Joe and Allan is a great team of plumbers. They gave me the right advice and helped me make a good decision with my heating."
Google review · May 2026
★★★★★
"The technical team is extremely efficient and skilled. They installed the water tank in two hours and the RUUD tank is working perfectly well."
Google review · May 2026
★★★★★
"We are so happy with the service provided by Joe and Alan. Alan was recommended to us to replace our hot water tank."
Google review · Feb 2026
★★★★★
"Highly recommend."
Google review · Jan 2026
★★★★★
"Canro boiler services were genuine life savers. I was stuck without heat overnight and they came by and got my boiler running."
Google review · Jan 2026
★★★★★
"Canro came in and fixed my boiler that was throwing all types of codes that I couldn't understand but the technician explained everything."
Google review · Jan 2026