🛡️ Licensed & Insured · TSBC Gas-Fitting LGA0043870 · Serving Metro Vancouver since 1999
★★★★★ 4.9 from 85+ Google reviews · info@canroheat.ca
Metro Vancouver HVAC · Since 1999

Viessmann Expansion tank Replacement Cost in Burnaby

A dripping pressure-relief valve on a Burnaby boiler is often the first clue that the expansion tank, not the valve, is the actual problem.

★ 4.9/5 · 85+ reviews✅ Licensed & insured💰 Rebates & financing👨‍🔨 Since 1999

Get your free quote

Tell us what you need—we’ll call you back fast.

No obligation · We never share your info

🎉
25+ YearsServing Metro Vancouver since 1999
★
4.9 / 5 Rating85+ verified Google reviews
🛡️
Licensed & InsuredTSBC LGA0043870 · Boiler LBP0046450 · Red Seal · WorkSafeBC
💵
Rebates HandledCurrent BC programs—eligibility checked before installation

Quick answer

An expansion tank replacement on a Viessmann boiler in Burnaby generally costs $200-$800 for parts and labour together. That figure is a 2026 public-market ballpark, not a fixed quote — CANRO's certified gas technicians confirm the exact cost once they've had a look at your specific system.

Need a licensed gas fitter for your gas boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.

The job the expansion tank is doing

Every closed hydronic heating loop needs somewhere for water to go as it expands with heat, and that's the expansion tank's whole purpose. It's a small pressurized tank with an internal bladder holding a cushion of air; as the water heats and expands, it pushes into the tank against that air cushion instead of driving the system pressure up. Over years of heating cycles, that bladder can rupture, or the tank can slowly lose its factory air pre-charge, and once either happens the tank stops absorbing anything and the rest of the system starts absorbing the pressure swings instead.

  • Pressure-relief valve drips or weeps, particularly after the heat has been running
  • Pressure gauge reads higher than usual once the boiler has been cycling
  • Banging or knocking pipes when the system starts up
  • The tank feels heavy and solid rather than having a hollow, half-air feel when tapped
  • The boiler shuts down on a high-pressure fault more than it used to

Burnaby specifics that come up on service calls

Burnaby is on the same soft, low-mineral Metro Vancouver reservoir supply as most of the region, so an expansion tank here fails from age and bladder wear rather than mineral scale eating away at it. What does vary across Burnaby is the mechanical room itself — older split-levels and post-war bungalows around areas like Edmonds and Cariboo sometimes have the boiler tucked into a compact utility space shared with laundry equipment, which can mean less room to maneuver a replacement tank in and out compared with the more open mechanical closets common in newer townhouse and condo developments near Metrotown and Brentwood.

A like-for-like expansion tank swap generally doesn't require a permit, but anything larger goes through the City of Burnaby, and the technician doing the gas-side work still needs a Technical Safety BC licence.

Cost breakdown for an expansion tank swap

Item2026 ballpark
Diagnostic / service call$90-$150, usually credited toward the repair
Labour$95-$165 per hour
Expansion tank, parts and labour$200-$800

These numbers reflect the broader 2026 market and aren't a set quote — a compact, older mechanical room can add labour time compared with an open, newer closet, which is what typically separates the low end of the range from the high end.

What can change the price

  • How much clearance there is to remove the old tank and fit a new one
  • Correct sizing of the replacement tank against the system's actual volume
  • Whether the pressure-relief valve needs to be replaced at the same time
  • OEM Viessmann part versus a compatible substitute, and the warranty difference
  • Age and condition of the isolation valve the tank connects through

Why it's a replace, not a repair

There isn't really a repair path for a failed expansion tank — once the bladder has ruptured or the tank won't hold its air charge, swapping it out is the standard and expected fix rather than trying to service the existing one. The one thing worth getting right is sizing: a technician matches the new tank to your system's actual volume rather than just installing whatever's closest in size, since an undersized tank will show the same symptoms again sooner than it should. If the boiler has needed several other unrelated repairs recently, that's a separate conversation about whether the unit as a whole is worth continuing to invest in.

Safety note

If you ever smell gas near the boiler, leave the house immediately and call FortisBC's emergency line at 1-800-663-9911 from outside — don't try to investigate it yourself. Gas-side boiler work must be done by a Technical Safety BC licensed gas fitter; CANRO holds gas licence LGA0043870 and boiler licence LBP0046450.

Frequently asked questions

How do I know it's the expansion tank and not the relief valve itself?

A dripping relief valve is often the visible symptom, but the two parts work together — a technician checks whether the tank is still holding its air charge before confirming the tank, not just the valve, needs replacing.

Can the tank be recharged with air instead of replaced?

If the bladder has failed, recharging won't hold pressure and the tank needs replacing. If it's only lost some pre-charge and the bladder is intact, a technician can advise if recharging is a realistic option for your specific tank.

Does Burnaby's water affect expansion tank life?

Not significantly — Burnaby is on the soft regional reservoir supply, so bladder age and wear are the main reasons a tank fails here rather than mineral scale.

Do I need a City of Burnaby permit for this?

Not typically for a like-for-like tank swap. Permits apply to larger scope work like venting changes or a full boiler replacement.

Is a dripping relief valve dangerous?

It's not typically an emergency, but ongoing dripping wastes water and signals a pressure issue worth diagnosing sooner rather than later.

Will a bigger tank prevent this from happening again?

The tank needs to be sized correctly for your system's volume, not simply larger — a technician calculates the right size rather than guessing up.

Related CANRO pages

Talk to a licensed CANRO gas fitter

Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.

Call (604) 359-1081 Email info@canroheat.ca
Good to know

Frequently asked questions

How long does a hot water tank last?
A standard gas or electric storage tank lasts 8–12 years. A high-quality tank with annual anode rod inspection can reach 15 years. Tankless water heaters typically last 18–22 years when descaled annually in Metro Vancouver's moderately hard water.
Should I switch to a tankless water heater?
Tankless makes sense if you have high demand (large family, multiple bathrooms running at once), want to free up floor space, or value endless hot water. Upfront cost is higher ($3,500–$6,000 installed vs $1,800–$3,200 for a tank) but operating cost is 25–40% lower for gas tankless.
My hot water tank is leaking — is it an emergency?
If the leak is from the tank body itself (not a valve or fitting), the tank is at end of life and needs replacement, usually within 24–48 hours before it floods. Shut off the water supply and gas/electric to the tank and call us.
What brands of water heaters do you install?
We install and service Bradford White, Rheem, AO Smith, John Wood, Giant, GSW for storage tanks; and Navien, Rinnai, Noritz, Bosch and Rheem for tankless units.
Can I install a water heater myself?
In BC, gas water heater installations must be performed by a TSBC-licensed gas fitter and are subject to permit and inspection. Electric tanks require a licensed electrician for the connection. CANRO handles permits as part of every installation.
What HVAC services does CANRO offer in Metro Vancouver?
CANRO installs, services and repairs boilers, furnaces, heat pumps, hot water tanks, tankless water heaters, gas fireplaces and air conditioning across Metro Vancouver. We work on residential homes, townhouses and condos throughout the Lower Mainland.
How long has CANRO been in business?
CANRO has been serving the Greater Vancouver area since 1999. Our founder George is recognised by customers as one of the most experienced boiler and hydronic heating technicians in the Lower Mainland.
What areas do you serve?
We cover all of Metro Vancouver: Vancouver, Burnaby, Richmond, Surrey, Coquitlam, North Vancouver, West Vancouver, New Westminster, Delta, Langley, Port Moody, Port Coquitlam, White Rock, Pitt Meadows, and Maple Ridge.
Keep reading

Related water heater articles

Reviews

What Metro Vancouver homeowners say

4.9
★★★★★
85+ verified Google reviews
★★★★★

“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”

Nadia Naderi
Nadia NaderiGoogle review
★★★★★

“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”

Arlene Colasurdo
Arlene ColasurdoGoogle review
★★★★★

“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”

B. Niek
B. NiekGoogle review

Need heat, hot water or cooling? Talk to a real technician today.

25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.

📞 Call (604) 359-1081 Get a free quote →
📞 Call nowFree quote