A symptom-first guide to how CANRO repairs American Standard gas furnaces in New Westminster homes.
Tell us what you need—we’ll call you back fast.
Quick answer
CANRO repairs American Standard residential gas furnaces in New Westminster by matching the symptom you're describing to the most likely cause, then confirming it with hands-on testing before recommending any part be replaced. Because the underlying components — igniter, gas valve, blower motor, control board — are standard across the furnace industry, the diagnostic logic is the same one we apply to every brand we service.
Need a licensed gas fitter for your gas furnace? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
| What you're noticing | Most likely area |
|---|---|
| Furnace won't start at all | Inducer, pressure switch, or igniter |
| Starts, then shuts off quickly | Flame sensor or limit switch |
| Weak heat, blower seems fine | Gas valve pressure or burner condition |
| Fan won't stop running | Limit switch or control board timing |
| Furnace works, but inconsistently | Control board or loose wiring connection |
The table above is a starting point, not a diagnosis — several different faults can produce very similar symptoms, which is exactly why we test rather than assume. A technician confirms the actual cause with a meter and direct component testing before recommending a repair, so you're not paying to replace a part that turned out not to be the problem.
CANRO is an independent, licensed HVAC and gas contractor. We service and repair American Standard furnaces along with other major brands, and we don't claim any factory-authorized or dealer relationship with the manufacturer.
Most single-fault repairs on an American Standard furnace in reasonable overall condition are straightforward to complete. It's worth a bigger conversation when the furnace is older and the current issue is one of several recent repairs, or when something more serious, like a heat exchanger concern, turns up during the visit — we'll compare repair cost against a new installation honestly rather than default to either option.
We'll also tell you plainly when a repair genuinely isn't worth doing — for example, a major component failure on a furnace already past a couple of decades in service, where the honest recommendation is to put the money toward a new installation instead of extending an aging system's life by a season or two.
New Westminster's character homes, particularly around Queen's Park and parts of Sapperton, sometimes have ductwork and venting that's been adjusted multiple times as furnaces were replaced over the decades, occasionally leaving venting routed in a way that's less than ideal by today's standards even if it's functioning adequately. When we're diagnosing a draft-related fault, we always check whether the venting itself is contributing before condemning a part like the inducer or pressure switch.
In more recently built homes, including much of Queensborough, ductwork and venting tend to be more consistently sized to the furnace installed, which generally means fewer airflow-related repeat faults and quicker diagnostic visits when something does go wrong.
Pricing reflects the part needed, diagnostic time, and site access. CANRO's office confirms the cost with you once diagnosis is complete, before any repair work proceeds.
Safety note
Repairs involving gas supply, ignition, or venting on an American Standard furnace are completed only by CANRO's licensed gas fitters. If you ever smell gas near your furnace, leave the home immediately and call FortisBC's emergency line at 1-800-663-9911.
No — CANRO is an independent, licensed HVAC and gas contractor that services and repairs American Standard furnaces along with other major brands, without claiming factory-authorized status.
This is most often a limit switch or control board timing issue, though it's worth checking the thermostat's fan setting first since some thermostats have a continuous-fan mode that's easy to enable by accident.
It can, since a clogged filter restricts airflow across the heat exchanger and reduces how much heat actually reaches your rooms. It's the first thing worth checking before booking a repair, though persistent weak heat after a filter change points to something else.
It's a helpful starting point for us to prepare, but not a substitute for hands-on testing, since several different faults can produce similar-sounding symptoms. We confirm everything on site before recommending a repair.
Yes, including homes with venting or ductwork that's been modified over multiple decades. We check the surrounding system, not just the part that seems to be failing.
The furnace's approximate age if you know it, a description of the symptom and when it started, and whether it's happened before are all helpful. None of it is required, but it can speed up diagnosis once a technician is on site.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.