CANRO's licensed gas technicians service and repair Lennox gas furnaces for Burnaby Heights homes, diagnosing the actual fault before recommending any work.
Tell us what you need—we’ll call you back fast.
Quick answer
CANRO services and repairs residential natural-gas Lennox furnaces for homeowners in Burnaby Heights, using standard Lennox-compatible parts sourced through regular HVAC supply channels. CANRO is not an authorized or factory Lennox dealer; a technician diagnoses the specific fault, whether it's ignition, airflow, or a control issue, before recommending a repair, and explains general wear points common to Lennox furnaces without referencing specific model or series numbers.
Need a licensed gas fitter for your gas furnace? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
Burnaby Heights is one of Burnaby's older, established neighbourhoods, with a mix of 1920s to 1940s character homes near the Hastings Street commercial strip and more recently renovated and infill properties on the surrounding blocks. Many of these homes have had their original gravity or oil furnace converted to a modern gas forced-air system at some point, and Lennox is one of the brands CANRO regularly sees and services in this area.
CANRO services Lennox furnaces as part of its general residential gas furnace work; CANRO is not a Lennox-authorized or factory dealer, and doesn't claim any special manufacturer status. What CANRO does bring is a licensed gas fitter's understanding of how forced-air furnaces generally fail and how to diagnose that fault correctly.
Like most gas forced-air furnaces, Lennox units commonly develop issues in a handful of predictable areas over years of service: the hot-surface ignitor, the flame sensor, the inducer motor that pulls combustion gases through the heat exchanger, and the control board that sequences the whole startup process. None of these are unique to Lennox; they're wear points shared across most residential gas furnace brands, and CANRO diagnoses them the same methodical way regardless of manufacturer.
The diagnostic approach starts the same way for any furnace brand: confirm the thermostat call, check for power at the control board, walk through the ignition sequence, and verify flame sense. Lennox control boards and blower modules have their own specific wiring and diagnostic behaviour, which a technician accounts for once the general fault category is narrowed down.
Older Burnaby Heights homes with retrofitted ductwork sometimes complicate diagnosis further, since undersized or poorly balanced ducts can cause a furnace to short-cycle on high-limit safety, which looks like a furnace fault but is actually an airflow problem upstream of the unit itself.
A Lennox furnace that's had one isolated component failure, with the heat exchanger and cabinet in good condition, is usually a solid repair candidate. A unit with repeated failures, visible corrosion, or a heat exchanger crack detected during inspection is a different conversation, since heat exchanger issues are a safety matter, not a routine repair, and typically point toward replacement.
CANRO gives an honest read on which category a given furnace falls into rather than defaulting to either option, and never claims to be an authorized Lennox dealer when discussing parts or warranty questions; those go back to the original installer or Lennox directly.
The CANRO office confirms pricing after a short conversation about the furnace's symptoms and age, and any repair is quoted before work begins on site. Most single-component repairs are completed in one visit once the part is confirmed compatible with the specific furnace.
Safety note
If you smell gas near the furnace or anywhere in the house, leave immediately and call FortisBC's emergency line at 1-800-663-9911 from a safe location before touching a switch or a phone inside. Furnace burners, gas valves, and venting must only be inspected, adjusted, or repaired by a Technical Safety BC licensed gas fitter.
No. CANRO services and repairs Lennox furnaces as part of its general residential gas furnace work, but is not an authorized or factory Lennox dealer.
CANRO sources standard Lennox-compatible parts through regular HVAC supply channels for common repairs. For parts still under manufacturer warranty, the original installer or Lennox may be the better first call.
The same wear points common to most gas furnaces after years of service: ignitor wear, a dirty flame sensor, an aging inducer motor, or control board issues. None of these are unique to the brand.
It depends on the specific fault, the unit's age and overall condition, and whether the heat exchanger shows any wear. A technician's inspection is the reliable way to answer this rather than guessing from symptoms alone.
Warranty terms are set by Lennox and vary by unit and registration; check your original paperwork or contact Lennox to confirm what's still covered before assuming either way.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.