A Raypak boiler in a new build gives you full control over sizing, zoning, and venting from the start, but that flexibility works best with early planning alongside your builder.
Tell us what you need—we’ll call you back fast.
Quick answer
A new-construction home gives you the advantage of designing the heating system around the boiler rather than working around whatever infrastructure already exists, which means a Raypak boiler can be matched precisely to a proper heat loss calculation, zoned exactly how the floor plan calls for, and vented in the most efficient location from day one. The key is coordinating the boiler selection early with your builder or designer, since radiant floor tubing layout, gas line sizing, and venting termination all need to be planned before framing and rough-in are finished, not decided after the fact.
Need a licensed gas fitter for your gas boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
New builds in Metro Vancouver increasingly use radiant floor heating, either throughout the home or in specific areas like bathrooms and basements, and a Raypak boiler is a common heat source for this kind of system. Radiant floor design requires the boiler's output and water temperature to be coordinated with the tubing layout and manifold zoning at the design stage, since retrofitting radiant tubing after concrete is poured or subfloor is installed isn't practical.
If the home also uses baseboard or forced-air heating in some areas alongside radiant floor in others, the boiler and its controls need to accommodate both types of heat emitter running at potentially different water temperatures, which is a more complex zoning setup than a single heat-emitter-type home.
A new build has no existing chimney or venting constraints to work around, which means the boiler's venting can be planned for the most efficient and least visually intrusive location on the home from the outset. Condensing Raypak models generally vent with PVC-style piping through a sidewall or roof termination, and coordinating that termination point with the architectural plans avoids awkward retrofitting after siding or roofing is complete.
This is also the point to plan condensate drainage properly, routing it to an appropriate drain during rough-in plumbing rather than improvising a solution after the mechanical room layout is finalized.
| New build consideration | Why it matters |
|---|---|
| Total gas appliance load | Boiler, range, fireplace, and dryer all draw from the same meter and main line |
| Gas line routing | Planned during rough-in, before drywall closes up the walls |
| Meter capacity | Confirmed against total household demand before finalizing appliance selection |
A new build often has several gas appliances — the boiler, possibly a gas range, a gas fireplace, a gas dryer — all drawing from the same meter and main line, so total household gas demand needs to be calculated and the line sized accordingly, ideally during the rough-in phase when it's straightforward to adjust rather than after walls are finished.
Bringing a licensed gas fitter into the planning conversation early, alongside your builder or designer, avoids the common new-build problem of mechanical decisions being made in isolation from each other. Radiant floor layout, boiler location, venting termination, and gas line routing all interact, and coordinating them upfront is considerably easier than making changes once framing, insulation, or drywall are in place.
Boiler installation costs for a new build generally fall within the same $6,500–$14,000+ ballpark, not a quote, as a retrofit, though a new build sometimes benefits from lower labour cost per component since walls are open and access is straightforward compared to working around an existing finished home.
Safety note
A Raypak boiler is a gas-fired, pressure-vessel appliance, and any work on the gas supply, venting, or the boiler's combustion and safety controls must be done by a Technical Safety BC licensed gas fitter holding a boiler licence as well. CANRO holds gas licence LGA0043870 and boiler licence LBP0046450. If you ever smell gas, hear unusual venting sounds, or suspect a carbon monoxide problem, leave the home immediately and call FortisBC at 1-800-663-9911 from outside before doing anything else.
As early as possible, ideally during the design or early framing stage, since radiant floor layout, gas line routing, and venting placement all need to be coordinated before rough-in is finished.
Yes, but the system's zoning and controls need to accommodate both heat emitter types, which sometimes operate at different water temperatures, so this needs to be planned at the design stage.
It depends on total household gas demand across all appliances — the boiler, range, fireplace, and dryer if gas — which should be calculated together to size the main line correctly.
It can be, since open walls and unfinished spaces make running piping and venting more straightforward, though the boiler and venting costs themselves fall in a similar ballpark either way.
It's much more difficult and costly to retrofit venting after siding or roofing is complete, so planning the termination point during the design phase is strongly preferred.
It's best to choose the boiler and confirm its output and water temperature requirements before the tubing layout and manifold zoning are finalized, since those details depend on the boiler's specifications.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.