Burnaby's older hillside homes generate a fairly consistent set of Slant/Fin repair calls, and CANRO — based right here — sees the same patterns year after year.
Tell us what you need—we’ll call you back fast.
Quick answer
A Slant/Fin boiler repair in Burnaby generally falls between $250–$1,800, most jobs landing $400–$900, plus the standard $90–$150 diagnostic visit. Consider that a starting-point figure from 2026 public market data, not a fixed quote; CANRO confirms the exact price once a certified technician has tested your unit's flow signal in person.
Need a licensed gas fitter for your gas boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
| Line item | Ballpark (CAD) |
|---|---|
| Diagnostic/service call (often credited to the repair) | $90–$150 |
| Licensed gas fitter labour rate | $95–$165 per hour |
| Typical Slant/Fin boiler repair bill (most jobs $400–$900) | $250–$1,800 |
Burnaby's older hillside neighbourhoods carry a lot of boilers that are original to homes built in the 1950s through 70s, which means repair calls here often involve components that have simply reached the end of their expected service life rather than a fresh installation issue.
Metro Vancouver's soft reservoir water generally means less scale-driven failure here than in areas on well water, so many Burnaby repair calls trace back to age and mechanical wear rather than mineral buildup.
A straightforward part swap on an accessible older unit stays toward the lower end. Cost climbs when a part has to be sourced for an older or discontinued model, when corrosion has seized a fitting, or when the underlying cast-iron radiator system needs a flush at the same time to resolve circulation problems.
Because so many Burnaby boilers are original to older homes, CANRO sees this decision come up often. A single isolated fault on a unit that's otherwise been reliable usually justifies repair. Once a unit needs a second or third major repair within a short span, or a hard-to-source control board, replacement typically works out better both financially and for reliability going into winter.
Hillside lots with narrow side yards can add a little time getting equipment or parts to the mechanical room, and CANRO factors that into scheduling for Burnaby calls. Demand for repairs typically spikes with the first sustained cold stretch of the season, so booking a non-emergency service visit ahead of that is worth considering on an older system.
A visit starts with pulling any fault history, testing system pressure, and inspecting the suspect component directly rather than guessing from symptoms alone. On a cast-iron radiator system, a technician also checks for sludge or scale in the piping, since a circulator or valve fault sometimes recurs quickly if the underlying water quality in the loop isn't addressed at the same time.
Since CANRO operates out of Burnaby, familiarity with the area's common housing eras and mechanical room layouts often speeds up an accurate diagnosis on the first visit.
Safety note
Boiler repair work involves gas piping, combustion, and venting. If you ever smell gas, hear an unusual burner sound, or suspect a carbon monoxide problem, leave the house immediately and call FortisBC at 1-800-663-9911. Diagnosis and repair on a gas boiler must be done by a Technical Safety BC licensed gas fitter — CANRO holds both a gas licence and a boiler licence.
That's often trapped air or mineral sediment in the system, sometimes called kettling, and a technician can flush or bleed the system to diagnose and resolve it.
It depends on the model and age — for some older units, sourcing an original control board or specific part becomes harder, which is part of the repair-versus-replace conversation.
It generally means less scale-related wear compared to well-water areas, though age and mechanical wear on older systems still lead to regular repair calls.
Both can cause uneven heating or a room that won't warm up, but they produce different symptoms a technician can distinguish with a proper diagnostic check rather than guessing.
It depends on what's failed and the unit's overall condition — a technician will lay out the repair cost against a replacement ballpark so you can compare rather than defaulting to either option.
Some non-urgent issues can, but a technician will tell you plainly if a fault poses a safety risk or is likely to worsen and leave you without heat mid-winter.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.