Radiant floor heating in a Fleetwood home runs off a gas boiler and depends on getting zoning and manifold placement right from the start.
Tell us what you need—we’ll call you back fast.
Quick answer
Radiant floor heating in Fleetwood is installed as loops of tubing connected to a manifold, fed by a gas boiler, either your existing one if it has the capacity or a new one sized for the added zone. The technician checks your boiler's output, the floor construction, and how the new zone will be controlled before laying out the design.
Need a licensed gas fitter for your gas boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
A fair number of Fleetwood homes are going through basement finishing or kitchen and bathroom renovations right now, especially in the older 1980s and 1990s subdivisions where owners are updating a house for a growing family or a secondary suite. Radiant floor heat is a popular add during these projects because it can go into a new slab or over an existing subfloor without needing new ductwork, which matters when a basement ceiling height is already tight.
The tubing layout depends on the floor construction. A new concrete slab in a basement renovation gets tubing embedded directly in the pour; an existing wood subfloor typically needs a low-profile panel system or tubing set into grooved boards. Loop spacing and length are calculated from the room's heat loss, not just its square footage, since a bathroom with an exterior wall needs different spacing than an interior hallway.
If your Fleetwood home already has a gas boiler heating baseboard or existing radiant zones, the technician checks whether it has enough spare capacity to add a new zone, and whether the water temperature the boiler runs at suits radiant floor tubing, which generally wants cooler supply water than baseboard. Sometimes that means adding a mixing valve to blend down the temperature for the new floor zone rather than replacing the whole boiler. In a home with no existing hydronic heat, a new boiler is sized to cover both the radiant zone and any other load it will serve.
Each radiant zone typically gets its own thermostat and a zone valve or circulator so it can run independently of the rest of the house. This matters in Fleetwood's mixed housing, where a basement suite addition often wants separate control from the upstairs living space. The manifold is the hub where all the loops for a given area come together and get balanced against each other.
| Element | What it does |
|---|---|
| Manifold | Splits and balances flow to each tubing loop |
| Mixing valve | Lowers boiler supply temperature to suit radiant tubing |
| Zone valve or circulator | Lets that area run independently of other zones |
| Thermostat | Controls when that zone calls for heat |
Radiant floor work involving a gas boiler requires a Technical Safety BC gas permit, coordinated through the City of Surrey, which CANRO applies for as part of the project. A single-room addition, like a basement bathroom, can often be completed in a day or two once the floor is open; a whole-basement radiant system with a new boiler takes longer and is usually scheduled around the broader renovation timeline.
Safety note
If you ever smell gas or suspect a leak, leave the home immediately, do not operate light switches, phones, or appliances inside, and call FortisBC's emergency line at 1-800-663-9911 from a safe location outside. Only a Technical Safety BC licensed gas fitter should open, adjust, or repair gas piping, venting, or combustion components. Boiler and gas line sizing for a new hydronic zone must be calculated and installed by a licensed gas fitter.
Often yes, if the existing boiler has spare capacity and the water temperature can be adjusted for the new zone; this is confirmed during the assessment.
Both work well; tile transfers heat most efficiently, while engineered wood needs product that is rated for radiant use and slightly different loop spacing.
Its own thermostat operates a zone valve or circulator dedicated to that loop, so it can run independently of other rooms.
Yes, since it involves gas boiler capacity and piping; CANRO applies for the Technical Safety BC gas permit as part of the installation.
A single room can often be done in a day or two once the floor is open; a full basement zone with new boiler capacity takes longer and is scheduled around the renovation.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.