The right boiler for radiant floors in Pitt Meadows depends on correct sizing for your home's heat loss and floor system, not on a specific brand or model being universally best.
Tell us what you need—we’ll call you back fast.
Quick answer
There is no single boiler model that's automatically right for every radiant floor system — the right choice is a correctly sized gas boiler matched to your home's heat loss, the tubing layout in your floors, and the water temperature the radiant system was designed around. Sizing errors, not brand choice, are what cause most radiant boiler problems.
Need a licensed gas fitter for your hot water / boiler? Call CANRO at (604) 359-1081 — residential natural-gas heating and hot water across Metro Vancouver since 1999.
Radiant heat runs at lower water temperatures than baseboard or radiators, spread across a large, slow-responding surface. A boiler sized and controlled for radiant needs different output and control logic than one intended mainly for domestic hot water or a higher-temperature system.
Many newer Pitt Meadows homes are built on slab-on-grade or have crawlspaces affected by the area's naturally high water table near the Fraser River floodplain. Radiant tubing embedded in a slab close to grade, in a home with a higher water table below, can have different heat loss characteristics than the same slab in a drier, higher-elevation area — insulation beneath the slab matters more here than it might elsewhere.
Homes on acreage properties with radiant additions to an older structure also need the boiler and controls to correctly serve both the new radiant zone and any existing higher-temperature distribution.
Correct sizing comes from a heat loss calculation specific to the home — insulation levels, window area, slab insulation, and ceiling height — not from square footage alone. This is especially relevant for slab construction, where under-slab insulation quality varies significantly between a recently built subdivision home and an older addition.
A new gas boiler install for a radiant system is generally in the ballpark of $6,500 to $14,000 or more, not a quote, and a full replacement is generally $7,500 to $15,000 or more, not a quote. The final number depends on boiler output, zoning, mixing valve needs, and site access.
If radiant floors are planned as part of new construction or a significant addition on a Pitt Meadows property, involving a heating technician early — alongside the builder and slab contractor — helps ensure the boiler, loop layout, and slab insulation are designed together rather than the boiler being an afterthought once the slab is already poured.
Beyond the boiler itself, the thermostats and zone controls chosen for a radiant system affect day-to-day comfort meaningfully, since radiant heat responds more slowly than forced air. A technician familiar with radiant systems can recommend controls suited to that slower response, rather than controls designed around a faster-reacting system, which can lead to noticeable temperature swings if mismatched.
Safety note
If you ever smell gas, hear an unusual hissing near the gas line, or suspect a venting or carbon monoxide problem, leave the home immediately and call FortisBC at 1-800-663-9911 from a safe location. Any gas line, venting, or combustion work must be carried out by a Technical Safety BC licensed gas fitter; CANRO holds gas licence LGA0043870 and boiler licence LBP0046450.
Yes — under-slab insulation quality affects heat loss meaningfully, and a technician should factor that into sizing rather than assuming standard heat loss for the home's square footage.
Often yes, using an indirect tank and appropriate mixing valves to supply the correct water temperature to each, though the system needs to be designed for it.
It can affect slab and crawlspace heat loss characteristics, which is worth factoring into the heat loss calculation for homes in lower-lying areas.
An oversized boiler tends to short-cycle on a low-load radiant zone, which wastes fuel and wears components faster than a correctly sized unit running longer, steadier cycles.
A licensed gas fitter or heating technician performs a heat loss calculation specific to your home's construction, rather than estimating from square footage alone.
Yes, if radiant floors are planned for new construction — involving them early ensures the boiler, loop layout, and slab insulation are designed together rather than added as an afterthought.
Family-run, TSBC-licensed (gas LGA0043870 · boiler LBP0046450), serving Metro Vancouver homes since 1999. Residential, natural gas only.
Call (604) 359-1081 Email info@canroheat.ca“Canro does an amazing job! Super professional and skilled with everything—boilers, furnaces, and AC. Always a pleasure working with them!”
“Five stars for Canro. We needed a replacement of a 30-year-old boiler. A new high-efficiency unit was installed—clean, professional work.”
“I can’t speak highly enough about George, who was recommended for a boiler service call for my parents’ home. George is excellent.”
25+ years keeping Metro Vancouver homes comfortable. Honest advice, upfront pricing, work that lasts.